Bradford White Electric Water Heater Reset Button Location Revealed

If you’re experiencing problems with your Bradford White electric water heater, such as no hot water or inconsistent temperatures, one of the first things to check is the reset button. The reset button is a safety feature that helps protect your water heater from damage in case of a power surge or other electrical issue.

How to Locate the Reset Button on a Bradford White Electric Water Heater

Locating the reset button on your Bradford White electric water heater is fairly simple.

Before resetting the button or switch, be sure to turn off the power to the water heater at the circuit breaker.

First, you’ll need to locate the access panel on the front of the unit. This panel is usually held in place by screws or clips, so you’ll need a screwdriver or pliers to remove it.

Once the access panel is off, you should see a small red button labeled “Reset” near the bottom of the unit.

Depending on the model of your Bradford White electric water heater, the reset button may be located on the thermostat or on the upper or lower heating element.

It’s important to note that not all water heaters have a reset button, so if you can’t locate it on your unit, consult the owner’s manual or contact a professional plumber for assistance.

In addition to the reset button, your Bradford White electric water heater may also have a high temperature limit switch that can trip and need to be reset. This switch is typically located near the upper heating element and may also be labeled “Reset” or “High Limit.”

If resetting the button or switch doesn’t solve the problem, there may be a larger issue with your

How to Reset Your Bradford White Electric Water Heater

Resetting your Bradford White electric water heater is a simple process that can be done in just a few steps. Here’s a step-by-step guide to help you reset your water heater:

Turn off the power: Before you begin, you’ll need to turn off the power to your water heater. Locate the circuit breaker that controls your water heater and flip it to the “off” position.

Locate the reset button: Next, locate the reset button on your water heater. Refer to the access panel or the manufacturer’s instructions if you’re having trouble finding it.

Press the reset button: Once you’ve found the reset button, press it down and hold it for a few seconds. This will reset the temperature control and should solve any issues you were experiencing with your water heater.

Also read: How to Fix Honeywell Temperature Sensor Failure 5 Flashes

Turn the power back on: After you’ve reset the water heater, turn the circuit breaker back on to restore power to the unit.

Wait for the water to heat up: Give your water heater some time to heat up. Depending on the size of your water heater and the temperature of your water supply, it may take anywhere from a few minutes to a few hours for the water to heat up.

Test the water temperature: Once the water has had time to heat up, test the temperature to make sure it’s at the desired setting. If it’s too hot or too cold, adjust the temperature control knob accordingly.

What to Do If Your Bradford White Electric Water Heater Keeps Tripping the Reset Button’

If your Bradford White electric water heater keeps tripping the reset button, it could be a sign of an underlying issue that needs to be addressed. Here are some troubleshooting tips to help you diagnose and fix the problem:

Check the wiring: If the wiring to your water heater is loose or damaged, it could cause the reset button to trip. Check the wiring connections and make sure they are tight and secure.

Inspect the heating elements: The heating elements in your water heater can become corroded or worn over time, which can cause the reset button to trip. Inspect the elements for signs of damage and replace them if necessary.

Check the thermostat: A faulty thermostat can cause your water heater to overheat, which can trigger the reset button. Check the thermostat settings and make sure they are set correctly.

Inspect the pressure relief valve: If the pressure relief valve is faulty or leaking, it can cause the water heater to overheat and trip the reset button. Inspect the valve and replace it if necessary.

If you’ve tried these troubleshooting tips and your water heater continues to trip the reset button, it’s best to contact a professional plumber for assistance. A qualified plumber can diagnose the issue and make the necessary repairs to get your water heater back up and running.